Homag PROFI BAZ20/30/16/V/D maskineringssenter for tre

This 4-axis HOMAG PROFI BAZ20/30/16/V/D was manufactured in 2003. It features a Homatic CNC control, WOODWOP CNC programming, an 18-position disk changer, and a main spindle with a 12 kW three-phase motor. Capable of handling workpieces up to 3000 mm in length and 1400 mm in width, it includes a continuous table with adjustable vacuum clamps. Consider the opportunity to buy this HOMAG PROFI BAZ20/30/16/V/D CNC Wood Machining Centre. Contact us for more information.
Location: DE
Control/Software: Homatic CNC control; WOODWOP CNC programming system; Postprocessor
Width adjustment (longitudinal console/D-table): Servo drive, per longitudinal console
Stop bolt for top layer overhang: Lifting/rotating device, max. 20 mm top layer, stroke 110 mm, individually selectable, end-position monitored (for manual door placement)
Configurations: 18 x Ø max. 130 mm; or 9 x Ø max. 180 mm + 9 x Ø max. 70 mm; grinding tools Ø max. 200 mm
Drilling/milling unit, 4 spindles: ER25 up to Ø16 mm shank, protrusion max. 50 mm, speed max. 13500 rpm, unlimited swivel via C-axis
Lock case milling unit, 2 spindles D=16/20: counter-rotating, 12000 rpm, integrated blow-out, unlimited swivel via C-axis
Swiveling saw/drill unit: manual 0–90°, flange Ø30 mm, TK Ø52 mm, prepared for crosscut saw Ø max. 180 mm, drill chuck with Weldon D=10 mm, speed max. 9000 rpm, C-axis swivel
Milling cutter holder D=30 with chip guide: mandrel length 45/80 mm, chip guide plate controlled via C-axis, changer space Ø 140 mm
Flush milling unit: simultaneous top/bottom, edge radius max. R12 mm, min. outer radius ~R5 mm / inner radius ~R30 mm at 90°, scanning top/bottom/side, unlimited C-axis swivel, speed max. 12000 rpm, workpiece thickness max. 50 mm, min. overhang ~35 mm, with narrow feeler shoes
WPL knife head: run-out angle 5°, Ø 70 mm
Drive spindle/V for gluing units: mounted right side of boom; cross slide with Y anti-reb and Z extension stroke; anti-reb spindle with C-axis and electrical/electronic interface; dedicated Z-axis
Gluing unit 4 sides, 90 mm (for main spindle): straight edges with direct glue application; 1 pre-press roller + 1 pneumatic post-press roller (programmable); inner radius min. R40 at 90°; edge height max. 90 mm; veneer thickness 0.4–1 mm; folding pressure zone on main spindle with hot-melt reactivation
Connectivity: Ethernet network connection
Chip conveyor belt: Integrated chip/scrap disposal via chip belt below longitudinal crossbars
Vacuum pump: 100/140 m³/h
Workpiece capacity
Length 800–3000 mm
Width 350–1400 mm
Thickness max. 70 mm with edge / 80 mm milling
Frieze width min. 120 mm
Weight max. 150 kg
Table/Clamping
Continuous table (D-table)
Longitudinal console 1 fixed
Longitudinal console 2 manual Y-width adjustment
8 vacuum clamps 125 x 50 x 100 mm
Working height lower edge of workpiece 950 mm
Unit for moving vacuum clamps on unit carrier with pneumatic extension console (max. 4 clamps per longitudinal console)
Main spindle
Speed 1500–18000 rpm (VFD 15 kW)
full rated power from 12000 rpm
Tool diameter max. 180 mm (milling) / 200 mm (grinding)
Room extraction for all tools/units
Aggregate interface/C-axis
Pneumatic and swivel drive interface
C-axis with torque drive and 3-point support
Tool changer
18-position disk changer for HSK F63
tool weight 6 kg
tool length max. 200 mm
Changer raisable for traveling pickup (left side)
Units/aggregates (for tool changer unless noted)
Gluing/edgebanding equipment
Edge hold-down device
manual adjustment
Magazine/pickup
Pickup space on X-support for interchangeable special unit (e.g
motor-driven swiveling machining spindle)
Additional equipment
External pre-chopping station with 3-stage roller
automatic
Roller turntable on operator side
roller Ø 800 mm
Edge length min. 350 mm
edge height max. 90 mm
Residual edge length monitoring with feed stop at 2400 mm