Conrad Conrad Combi 500 HD borerigg






























Dersom du bestemmer deg for å kjøpe utstyr til en lav pris, sørg for at du kommuniserer med den ekte selgeren. Finn ut så mye informasjon som mulig om eieren av utstyret. En måte å jukse på er å presentere deg selv som en ekte bedrift Ved mistanke, informer oss om dette for ekstra kontroll, via tilbakemeldingsskjemaet.
Før du bestemmer deg for å gjøre et kjøp, se nøye på flere salgstilbud for å forstå den gjennomsnittlige prisen på det valgte utstyret. Dersom prisen på tilbudet du liker er mye lavere enn lignende tilbud, tenk over saken. En betydelig prisforskjell kan indikere skjulte defekter eller et forsøk fra selgeren til å utføre ulovlige handlinger.
Ikke kjøp produkter der prisen er for ulik fra gjennomsnittsprisen for lignende utstyr.
Ikke gi samtykke til tvilsomme pantsettelser og forhåndsbetalte varer. Ved tvil, ikke vær redd for å oppklare detaljer, spørre om flere bilder og dokumenter for utstyret, og sjekk autentisiteten til dokumentene, still spørsmål.
Den mest vanlige typen svindel. Urimelige selgere kan be om et visst beløp i forhåndsbetaling for å «reservere» din rett til å kjøpe utstyret. På denne måten kan svindlere samle inn et stort beløp og forsvinne, og aldri ta kontakt igjen.
- Overføring av forskuddsbetaling til kortet
- Ikke utfør en forhåndsbetaling uten å ha dokumenter som bekrefter overføringen av pengene, dersom selgeren under prosessen virker tvilsom.
- Overføring til en forvaltningskonto
- En slik forespørsel er alarmerende, og mest sannsynlig kommuniserer du med en svindler.
- Overføring til en firmakonto med et lignede navn
- Vær varsom, svindlere kan utgi dem selv for å være anerkjente selskaper, ved å gjøre små endringer på navnet. Ikke overfør penger dersom selskapets navn er tvilsomt.
- Utskiftning av egne detaljer på fakturaen til et ekte selskap
- Bør du utfører overføringen, sjekk at de spesifiserte detaljene er riktige, og hvorvidt de faktisk hører til det spesifiserte selskapet.
Selgers kontakter



















- in stock!
= Remarks =
The Conrad Combi 500 HD is a crawler-mounted drilling rig designed for reverse circulation, airlift reverse circulation, percussive drilling, and direct-circulation rotary drilling.
Includes 28 drill pipes with an outer diameter of 160 mm and an inner pipe of 130 mm 400 cm long.
The rig is mounted on a hydraulically driven crawler undercarriage measuring approximately 2.5 m in width, 4.6 m in length, and 0.85 m in height. The tracks are 600 mm wide and fitted with rubber pads. The frame features four independently operated hydraulic outriggers—two at the front and two at the rear—with a stroke of 1,000 mm. A hydraulic turntable allows the machine to rotate 360° in either direction without moving the tracks.
Power is provided by an Iveco FPT-C87-ENTZ Tier 4 / Stage IIII Final diesel engine delivering a maximum of 305 kW (415 hp) at 2,100 rpm. Maximum engine torque is 1,800 Nm at 1,500 rpm. The engine is housed in a sound-attenuated stainless steel enclosure with an integrated fuel tank; the tank capacity is optimized to a maximum of approximately 500 liters. The machine is equipped with an air compressor for pneumatic tools, rear-mounted air connections, and an additional low-mounted start switch.
The hydraulic system powers all drilling, travel, and auxiliary functions. An IQAN electrical control system monitors and operates the hydraulic functions; in the event of a malfunction, an emergency program allows the system to switch to manual control.
The drill mast is a welded box-section structure that is raised and lowered hydraulically. The mast features a travel range of up to 1.4 m and a maximum pullback force of approximately 40 tonnes when using the bottom clamp. For angle drilling, the mast can be adjusted from 90° to approximately 60° in 5° increments.
The pullback and pulldown system has an effective stroke of approximately 6 m. The maximum pullback force is 20,000 daN, and the maximum pulldown force is 9,000 daN. Normal pullback speed ranges from 0 to 0.3 m/s, high pullback speed from 0 to 0.65 m/s, and the maximum pulldown speed is 0.6 m/s. The machine includes a bit-weight control system.
The top drive has a diameter of 6 inches and a bore of 150 mm. In high-torque mode, it delivers 2,000 daNm at 10 to 50 rpm. In low-torque mode, it delivers 1,000 daNm at 10 to 100 rpm. Torque and rotational speed are adjustable from the control panel, where the speed is also displayed. A hydraulic breakout device located below the top drive provides up to 4,000 daNm of additional breakout torque. An air swivel is mounted below this device to supply air to the airlift drill pipes.
The hydraulic chuck and bottom clamp are designed for 5-inch double-walled airlift drill pipes. The bottom clamp can open laterally to provide unobstructed access to the borehole. The clearance beneath the clamp ranges from approximately 250 mm to 1,650 mm, depending on the mast adjustment. As a safety measure, the lower clamp and the chuck cannot be depressurized simultaneousl
= Dealer information =
Interested? We would be happy to make you an excellent offer! Send an email to vis kontakter or call vis kontakter.
Do you have a question about an advertisement, drill, pump, part, or order? Or would you just like to discuss what would be useful in your situation?
Don't keep worrying about it, just give us a call.
We are available Monday through Friday between 7:00 a.m. and 6:00 p.m. Call, text, or email us, whichever you prefer.
Want to visit us? Yes, please!
Our doors are open Monday through Friday from 7:00 a.m. to 4:00 p.m. On Saturdays, you are welcome by appointment.
= More information =
Model year: 2015
Field of application: Construction
Carrying capacity: 5.000 kg
GVW: 32.000 kg
General condition: good
Technical condition: good
Visual appearance: good
Emissions class: Stage IV
Please contact Gert-Jan Kruitbosch or John van Tongeren for more information